troubleshooting of top laser welding machine

　　The top laser welding machine in the use of the process will more or less appear some faults, in order to make the laser welding machine work better, reduce the number of failures, increase the efficiency of work, we must understand the operation of the process should pay attention to the problems and troubleshooting methods. Below, the Otlaser laser marking machine supplier will analyze some common fault treatment methods of the top laser welding machine for you.
　　
1. When the laser welding is wrong, press the emergency stop button in time, the system will automatically cut off the laser control, the servo motor power supply, to prevent accidents, the emergency stop must be initialized after the spring operation;
　　
　　2 of roof, the laser welding machine welding equipment runtime exception to stop: check the touch screen alarm screen related alarm, there is alarm device will automatically switch to the suspended state and reset button will be shining with the frequency of 0.2 s, at the same time a buzzer to 1 s frequency chirping and trichromatic lamp normally on a red light, solve relevant alarm according to the alarm reset button to reset the alarm, and then press the start button to continue to run;
　　
　　3. When the equipment of the top cover pre-welding laser welding machine does not operate, please check whether there is relevant alarm on the touch screen or whether the equipment is suspended or waiting for material:
　　
　　Reset alarm of the whole machine: the whole machine can only operate if the laser welding machine of the pre-welding of the top cover needs to be reset;
　　
　　1. Axis ALM alarm: simply reset the axis alarm in the function window or press the alarm reset button;
　　
　　2. Limit alarm: it indicates that the motor reaches the soft limit and can only run in the opposite direction without reset;
　　
　　3. Note: a few minutes for the equipment of the top cover pre-welding laser welding machine:
　　
　　4, when the operation of the laser is not under control, need to quickly press the emergency stop button, the emergency stop button will stop sending laser signals and welding shaft power off, after processing the failure of the emergency stop button, the top pre-welding laser welding machine reset and re-run the program.
　　
　　The welding will automatically stop dust removal and nitrogen blowing if it lasts for one minute;
　　
　　After the alarm is cleared, the beeping sound will occur again one minute later.
　　
　　Only 1PCS of on-line body material will be supplied automatically when it lasts for one minute;
　　
　　After the failure, we can refer to the above content for operation check.

评论

发表评论

此博客中的热门博文

OTLASER is the best china laser marking system supplier

　　OTLASER was recognized as China laser marking system  supplier ,OTLASER has 14 years of R&D experience, with a factory area of ​​nearly 3,000 square meters. The technical department has more than 100 senior staff members,367 patents;Now it has realized two core technologies: laser cutting system and laser marking system. 　　 　　Nowadays, OTLASER has a complete product line, including: fiber laser cutting machine series, co2 fiber laser series, uv laser series, 3d laser series and 10000W, 12000W, 15000W, high power laser cutting machine etc. The high power fiber laser cutting machine is one of the best laser manufacturers in China. These products have not only been recognized by China, but also exported to more than 30 countries and regions. 　　 　　OTLASER has fully automatic chip packaging and automated patch technology, and has realized the self-production of dozens of core optical components such as, pump source, QBH, collimator, combiner, isolator, acousto-optic modulator, et
阅读全文

3D laser cutting machine Specification

图片
The working mechanism of 3d laser cutting 　　 Laser cutting is the use of high power density laser beam scanning over the material surface, in a very short period of time to heat the material to thousands to tens of thousands of degrees Celsius, so that the material melting or gasification, and then high pressure gas will melt or gasification material blown away from the slit, to achieve the purpose of cutting materials. 　　The working mechanism of 3d laser cutting is relatively different from that of 2d laser cutting. 3d laser cutting requires constant adjustment of laser cutting head position to ensure that the laser cutting head is always perpendicular to the workpiece surface, so as to obtain excellent cutting quality. In actual production, 3d laser cutting program compilation requires the 3d modeling of parts, and then the introduction of 3d programming system generation path, and manual adjustment according to the characteristics of parts, tooling features, to avoid cutting head
阅读全文

The principle of laser cutting machine

图片
　　The principle of laser cutting machine 　　 　　 Laser cutting is to make the irradiated material melt, vaporize, ablate or reach the ignition point by irradiating the workpiece with the focused high power density laser beam, and at the same time remove the molten material by means of the high-speed airstream coaxial with the light beam, so as to realize the cutting of the workpiece. Laser cutting is one of the thermal cutting methods. The principle of laser cutting is shown below. 　　 Types of laser cutting 　　 　　Laser vaporization cutting is mainly used for cutting extremely thin metal materials and non-metal materials (such as paper, cloth, wood, plastics and rubber, etc.). 　　 　　1. Fusion cutting 　　 　　During laser fusion and cutting, metal materials are melted by means of laser heating, and non-oxidizing gases (Ar, He, N, etc.) are sprayed by the nozzle. Liquid metal is discharged by the strong pressure of the gas to form an incision. It only takes a tenth of the energy to
阅读全文